Look for products:
    
Home > Choose a Manufacturer > Microlog Technologies
Sort By:
Page of 3
Microlog Distribution Panel Hinges
Microlog Distribution Panel Hinges

Anodized Black Aluminum Hinge will fit panels on left side.
Comes with Magnetic SNAP closure and hardware on right side.
HG-7: Hinge Option for 12DC-DMM Panel
HG-10: Hinge Option for 20DC-DMM Panel
Bugbuster Hatch Insect Screen
Bugbuster Hatch Insect Screen

Installation is a cinch, just put the Bugbusters over the hatch and the generous dimensions allow the hatch to open fully from inside for maximum ventilation.
Features & Specs:
- 100% Mil Spec Polyester mesh
- 600 Very small Holes/Inch, No-see-um proof
- Lead ballasted (will not affect compass)
- Installs instantly over any hatch
- No attachments necessary
- Allows easy adjustment of hatch opening from inside
- Stows in a strong plastic carrying case
Bugbuster Companionway Insect Screen
Bugbuster Companionway Insect Screen

A simple solution for no-see-ums, mosquitos and other bugs...
The unique to the market companionway model ties to the handrails and drops down to the cockpit floor. No velcro or frame needed. Allows full companionway opening permitting very easy access to and from the cockpit.

Features & Specs:
-100% Mil Spec Polyester mesh, military spec, flame retardant
-600 very small holes/inch, No-see-um proof
-Lead ballasted (will not affect compass)
-Installs easily by attaching to hand rails with built-in ties
-Allows easy access to and from cockpit
-Stows in a strong plastic carrying case

Sizing Information:
72” long x 36” wide (91cm x 183cm) - Standard: fits most small sailboats
78” long x 42” wide (198cm x 107cm) - Bigger Rectangular size, Good for big catamarans, powerboats
77” long x 40” wide (196cm x 102cm) - Fit many Beneteau's and Jeanneau's, MacGregor 26X (tapering to 28" wide at bottom)
68” long x 48” wide (173cm x 122cm) - Catalina (except 30, 380, 400), Caliber, Endeavour (tapering to 28" wide at bottom)
44” long x 38” wide (112cm x 97cm) - Catalina 380, 400 (tapering to 29" wide at bottom)
68” long x 60” wide (173cm x 152cm) - Catalina 30 (tapering to 28" wide at bottom)

To Measure:
Just take maximum inside companionway measurement and add 3 inches on each side and on top to fit neatly.
Example: A 30" x 68" inside opening, would use a 36" x 72" screen.On the tapered screens, the tapering begins at the halfway point of the length, 34" and 39" respectively. For the 44 x 38 screen, the taper begins at 26 inches.
Microlog Shunt and Wiring Kit [SWK-105]
Microlog Shunt and Wiring Kit [SWK-105]
Our Price: $46.49

SWK-105 Shunts and Wiring kit: Required if you need to measure current up to 100 AMPS.

For systems with maximum current of 100 A or 65 A continuous with no overloads, or 50 amps continuous with overload to 100 amps for 8 seconds max. These are suitable for small systems, or for most applications where you want to measure only solar or wind turbine input current. It allows "amps" readings as low as 0.1 Amp.

Kit includes:
-100 Amp. Marine Grade Shunt
-20 feet PVC jacketed, tinned, flexible marine grade wire for exact calibration of your instrument
-Connectors to shunts and Brass screws


Shunts Specifications:

Current limit:
100 Amp.
Continuous Current limit:
65 Amp.
Surge limit(25°C):
100 Amp.,8 sec/min. MAX
(Derating as ambiant temperature rise)
Size:
2.00" L. x 1.25" W. x 1.75" D
5,1 cm x 3,2 cm x 4,4 cm.
Microlog Shunt and Wiring Kit [SWK-505]
Microlog Shunt and Wiring Kit [SWK-505]
Our Price: $58.99

SWK-505 Shunts and Wiring kit: Required if you need to measure current up to 500 AMPS.

For systems with maximum current of 500 A or 330 A continuous with no overloads, or 250 amps continuous with overload to 500 amps for 8 seconds max. These are suitable for high current Inverters consumption, charging alternator, solar panels, wind turbines and NET Amps. It allows "amps" readings as low as 1 Amp.

Kit includes:
-500 Amp. Marine Grade Shunt
-25 feet PVC jacketed, tinned, flexible marine grade wire for exact calibration of your instrument
-Connectors to shunts and Brass screws

Shunts Specifications:

Current limit:
500 Amp.
Continuous Current limit:
330 Amp.
Surge limit(25°C):
500 Amp.,8 sec/min. MAX
(Derating as ambiant temperature rise)
Size:
3.25" L. x 1.75" W. x 1.75" D
8,2 cm x 4,4 cm x 4,4 cm.
Microlog Battery Monitor 12/24V [DMM-3-BR]
Microlog Battery Monitor 12/24V [DMM-3-BR]
Our Price: $89.99

DMM-3-BR for 2 Battery Banks + Amps
**Needs SWK-105 or SWK-505 for Amp Measurement

Microlog designed the perfect little Battery and DC current monitor at an affordable price. Check the House Bank or the twin engine start batteries critical voltages, Also Check current circulation in the system at glance, find charging problems or Phantom power losses. Unique on market! an extremely low current consumption of 1.8 mA, so low you can leave it ON all week*...

Precision Voltage Monitoring:
The Microlog DMM-3 (2 Batt.)/ DMM-4 (3 Batt.) Battery Monitors are designed to monitor the level of charge for 2 or 3 battery banks in measuring the Total Battery Cells Voltages with great precision. The voltage monitoring will help telling you the state and condition of your batteries, charging equipment and also when it's time to charge and stop charging.

Charge and discharge current monitoring (with shunt kits, see below):
The Microlog DMM-3 / DMM-4 System will also monitor the intensity (Amperes) of incoming current from charging equipment such as alternators, wind generators or solar panels and/or, current consumed in your boat or RV. You can measure just charging or just discharging current if you prefer; or NET current circulation to your House bank, your choice. Charging current will be represented with a "+" sign and discharging current with a "–" sign.The instrument measures the slight potential difference between shunt terminals and translate this measurement in Amperes (Shunt is optional).

Backlit Display:
Our monitors comes with a Red backlit display for night monitoring with very high efficiency LEDs for low current drain.

Plug and Play:
The system is easy to install and operate. Drill a small hole for wires, peel 3M™ adhesive pads and put in place. No programing or resets of any kind; simply press the right button for functions (battery #1 active by default).

As good as it gets:
The Microlog Monitors are carefully made with the finest components and materials in order to optimize its reliability and performance, such as: Use of Surface-Mount Technology (SMT), Anti-Corrosion Treatment, Sealed Adjustments Trimmers, Lexan® Facing and Stainless Steel Hardware for harsh marine environment.

The Microlog instruments are covered with a 2 year limited warranty.
Microlog Battery Monitor 12/24V [DMM-4-BR]
Microlog Battery Monitor 12/24V [DMM-4-BR]
Our Price: $99.99

DMM-4-BR for 3 Battery Banks + Amps:
**Needs SWK-105 or SWK-505 for Amp Measurement

Microlog designed the perfect little Battery and DC current monitor at an affordable price. Check the House Bank or the twin engine start batteries critical voltages, Also Check current circulation in the system at glance, find charging problems or Phantom power losses. Unique on market! an extremely low current consumption of 1.8 mA, so low you can leave it ON all week*...

Precision Voltage Monitoring:
The Microlog DMM-3 (2 Batt.)/ DMM-4 (3 Batt.) Battery Monitors are designed to monitor the level of charge for 2 or 3 battery banks in measuring the Total Battery Cells Voltages with great precision. The voltage monitoring will help telling you the state and condition of your batteries, charging equipment and also when it's time to charge and stop charging.

Charge and discharge current monitoring (with shunt kits, see below):
The Microlog DMM-3 / DMM-4 System will also monitor the intensity (Amperes) of incoming current from charging equipment such as alternators, wind generators or solar panels and/or, current consumed in your boat or RV. You can measure just charging or just discharging current if you prefer; or NET current circulation to your House bank, your choice. Charging current will be represented with a "+" sign and discharging current with a "–" sign.The instrument measures the slight potential difference between shunt terminals and translate this measurement in Amperes (Shunt is optional).

Backlit Display:
Our monitors comes with a Red backlit display for night monitoring with very high efficiency LEDs for low current drain.

Plug and Play:
The system is easy to install and operate. Drill a small hole for wires, peel 3M™ adhesive pads and put in place. No programing or resets of any kind; simply press the right button for functions (battery #1 active by default).

As good as it gets:
The Microlog Monitors are carefully made with the finest components and materials in order to optimize its reliability and performance, such as: Use of Surface-Mount Technology (SMT), Anti-Corrosion Treatment, Sealed Adjustments Trimmers, Lexan® Facing and Stainless Steel Hardware for harsh marine environment.

The Microlog instruments are covered with a 2 year limited warranty.
Microlog Shunt and Wiring Kit for DMM-1 [SWK-205]
Microlog Shunt and Wiring Kit for DMM-1 [SWK-205]
Our Price: $104.99

The SWK-205 Shunts and Wiring kit is required if you need to measure current up to 135 Amp. Continuously. Users with alternators over 135A and 1800-2000W inverters should use SWK-225.

Kit includes:
-Dual 200 Amp. (135 Amp. continuous) Marine Grade Shunts
-25 feet PVC jacketed, tinned, flexible marine grade wire for exact calibration of your DMM-1 instrument
-Connectors to shunts and battery poles

Dual 200 Amp. shunts which are made with naval specification brass.
Microlog Shunt and Wiring Kit for DMM-1 [SWK-205]
Microlog Heavy-Duty Shunt and Wiring Kit for DMM-1 [SWK-225]
Our Price: $136.99

The SWK-225 Shunts and Wiring kit is required if you need to measure current up to 200 Amp such as Hi-Amp alternators or 1800-2000 W. inverters. Millitary specs with silver soldering of plates and ROHS

Kit includes:
-Dual 200 Amp. Heavy Duty Marine Grade and Military spec shunts
-25 feet PVC jacketed, tinned, flexible marine grade wire for exact calibration of your DMM-1 instrument
-Connectors to shunts and battery poles


Dual 200 Amp. shunts which are made with naval specification brass.
Microlog Battery Monitor 12/24V [DMM-4]
Microlog Battery Monitor 12/24V Kit - includes shunt and wiring [DMM-4-BR201]
Our Price: $149.99

DMM-4-BR201: NEW KIT!! 12-24V, Monitors 3 Batteries + Amps / RED Backlit Display with 200A shunt and wiring.

Microlog designed the perfect little Battery and DC current monitor at an affordable price. Check the House Bank or the twin engine start batteries critical voltages, Also Check current circulation in the system at glance, find charging problems or Phantom power losses. Unique on market! an extremely low current consumption of 1.8 mA, so low you can leave it ON all week*...

Precision Voltage Monitoring:
The Microlog DMM-3 / DMM-4 Battery Monitors are designed to monitor the level of charge for 2 or 3 battery banks in measuring the Total Battery Cells Voltages with great precision. The voltage monitoring will help telling you the state and condition of your batteries, charging equipment and also when it's time to charge and stop charging.

Charge and discharge current monitoring (with shunt kits, see below):
The Microlog DMM-3 / DMM-4 System will also monitor the intensity (Amperes) of incoming current from charging equipment such as alternators, wind generators or solar panels and/or, current consumed in your boat or RV. You can measure just charging or just discharging current if you prefer; or NET current circulation to your House bank, your choice. Charging current will be represented with a "+" sign and discharging current with a "–" sign.The instrument measures the slight potential difference between shunt terminals and translate this measurement in Amperes (Shunt is optional).

Backlit Display:
Our monitors comes with a Red backlit display for night monitoring with very high efficiency LEDs for low current drain.

Plug and Play:
The system is easy to install and operate. Drill a small hole for wires, peel 3M™ adhesive pads and put in place. No programing or resets of any kind; simply press the right button for functions (battery #1 active by default).

As good as it gets:
The Microlog Monitors are carefully made with the finest components and materials in order to optimize its reliability and performance, such as: Use of Surface-Mount Technology (SMT), Anti-Corrosion Treatment, Sealed Adjustments Trimmers, Lexan® Facing and Stainless Steel Hardware for harsh marine environment.

The Microlog instruments are covered with a 2 year limited warranty.